5 Brother Printer Error Messages That Are Commonly Occur

A big fact is that Brother printer error messages are everywhere, so are the ways. Some of the error messages are unable to print, replace toner, drum error, error codes, paper jam and many others.

Here you will find the list of the most common error message on Brother printer along with the fix tips to solve them.

Unable To Print Error 30

The first and most common error message on Brother printer is unable to print error 30. The error code 30 means the “Unable to print” indicating that the device could not perform of printing because of the mechanical malfunction.

Other possible cause is an object that gets stuck in the device such as a piece of paper or a paper clip.

So fix it by following these simple steps:

1. Lift the scanner with your both hands to allow it for an open position.

2. Check if there is any object jammed in the machine. Remove it and turn around the printer to open the jam clear cover on the back. This is aimed to check other objects jammed there. If there is any, remove it from the machine.

Recommended:  Brother HL-2170W Wireless Setup & Manual

3. Close the covers and continue the printing job.

Brother Printer Laser Unit Error

If you receive Brother printer error messages with the error code 51, it means that there is a problem with the laser unit.

This way, it is very possible that you don’t put the cover into its proper position. To fix this problem, you can simply open the printer up and make sure it is installed correctly.

However, if Brother printer error code 51 keeps appearing on your LCD, you could try to switch the printer off and back on again.

It is due to the fact that part of the laser unit is probably very defective. So you can solve the problem by replacing the laser unit.

Brother Error Fuser Unit Malfunction

Fuser unit malfunction is the other Brother error. Usually the error appears as error code 50.

The basic reason why your Brother could not printing is the fuser unit that is getting too hot during the printing session, making the machine unable to print anymore.

Recommended:  How to Fix Brother Printer No Paper Error (4 Solutions)

To solve this problem, the simple procedure you can try is to turn off the printer and wait for 5-10 minutes.

Afterwards, turn on the printer again and wait for 10 minutes, too. If you are still receiving the same error message, it is likely that you need to replace the fuser unit with the new one.

Brother Error Code 48

Brother error code 48 means that the printer’s head cable or circuit board is not only broken but also getting damaged.

That could be caused by the foreign objects such as paper clips or a piece of paper that get stuck in the printer. As a result, the printer is unable to print.

It is easy to fix this issue. Simply you need to turn off the printer device and life the scanner cover using your both hands.

Look for any objects that remain inside the printer. If there is any, don’t hesitate to remove it as soon as possible.

Then, close the cover and do print test. If the same error message still appears, it indicates that the encoder strip of the device must be clean off.

Recommended:  Brother HL-L2350DW Wifi Setup & Manual

The encoder strip is located in front of the vinyl band within the device. Just use the dry cloth and carefully clean the strip.

Later, turn on the printer and make a print job to see if the problem has been solved.

Brother Printer Error TS-02

If your Bother printer experiences error TS-02, it is one of the most common Brother printer error messages occurs in the device.

Truly, this kind of error occurs when the wireless access point cannot connect to the printer’s MAC address.

Perhaps, it is due to the damages, corrupted system file entries, improper installation and other hardware issues.

So here are the steps to fix the problem:

1. Make sure that the internet connection is strong enough and the WLAN router properly works.

2. Place the device close to the WLAN access point to get a better connectivity.

3. Allow the MAC address in the filter.

4. Check whether your device and the system use the same range of radio signals.

5. Use the Setup Wizard option for more established connectivity.

Stella Nelson

Halo, Saya adalah penulis artikel dengan judul 5 Brother Printer Error Messages That Are Commonly Occur yang dipublish pada di website QuickStare.com

Artikel Terkait